Rfid Reader Using Nodemcu Esp8266 & Visuino
About the project
In this project we are going to read RFID tags using NodeMcu ESP8266 & Visuino and display tag ID on the OLED Display. Watch the Video!
Project info
Difficulty: Easy
Platforms: Arduino, SparkFun, Visuino
Estimated time: 1 hour
License: GNU General Public License, version 3 or later (GPL3+)
Items used in this project
Hardware components
Story
- NodeMCU ESP8266 (or any other board)
- OLED Display
- MFRC522 RFID Reader module
- Breadboard
- Jumper wires
- Visuino program: Download Visuino
- Visuino RFID component: Download RFIT Tag Read
- Connect NODEMCU ESP8266 Pin [3V3] to RFID pin [3.3V]
- Connect NODEMCU ESP8266 Pin [3V3] to OLED pin [Vcc]
- Connect NODEMCU ESP8266 Pin [GND] to RFID pin [GND]
- Connect NODEMCU ESP8266 Pin [GND] to OLED pin [GND]
- Connect NODEMCU ESP8266 Pin [D1] to RFID pin [RST]
- Connect NODEMCU ESP8266 Pin [D2] to RFID pin [SDA]
- Connect NODEMCU ESP8266 Pin [D3] to OLED pin [SCL]
- Connect NODEMCU ESP8266 Pin [D4] to OLED pin [SDA]
- Connect NODEMCU ESP8266 Pin [D5] to RFID pin [SCK]
- Connect NODEMCU ESP8266 Pin [D6] to RFID pin [MISO]
- Connect NODEMCU ESP8266 Pin [D7] to RFID pin [MOSI]
Start Visuino as shown in the first picture Click on the "Tools" button on the Arduino component (Picture 1) in Visuino When the dialog appears, select "NodeMCU ESP-12" as shown on Picture 2
Step 4: Set the Board and RFID Component
- First Add "RFID TAG READ (SPI)" component to Visuino, you can download it hereand on the page is also a step by step tutorial on how to add it to Visuino
- In Visuino Select "NodeMCU ESP-12" board and in the properties window set I2C pin [SCL] to 3 and set I2C pin [SDA] to 4
- Add "RFID 522 SPI" component
- Add "OLED I2C" component
- Double click on the "DisplayOLED1" and in the "Elements" window drag "Draw text" to the left side and in the properties window set "Size" to 2 and "Text" to ID
- Drag "Text Field" to the left side and in the properties window set "Size" to 2 and "Y" to 30
- Close the "Elements" window
1 / 3
- Connect "RFID5221" pin [SPI] to "NodeMCU ESP-12" pin [SPI]
- Connect "RFID5221" pin [Chip Select] to "NodeMCU ESP-12" digital pin [2]
- Connect "RFID5221" pin [Reset] to "NodeMCU ESP-12" digital pin [1]
- Connect "RFID5221" Key pin [Out] to "DisplayOLED1" > "TextField1 " pin [In]
- Connect "DisplayOLED1" Out pin [I2C] to "NodeMCU ESP-12" I2C pin [In]
In Visuino, at the bottom click on the "Build" Tab, make sure the correct port is selected, then click on the "Compile/Build and Upload" button.
Step 8: PlayIf you power the NodeMcu ESP8266 board and place the RFID Card on the RFID module the OLED Display will show the Tag ID.
Congratulations! You have completed your project with Visuino. Also attached is the Visuino project, that I created for this Instructable, you can download it and open it in Visuino: https://www.visuino.com
Schematics, diagrams and documents
Code
Credits
Related products
Leave your feedback...